How to Care for and Maintain Exterior Stucco

stucco maintenance

Stucco is a convenient fine plaster for homeowners. It is durable and easy to maintain. It gives a nice architectural decoration for your home. If you apply stucco properly, it can last up to 50 years. Maintenance is the key to long-lasting stucco. Although stucco is easy to maintain and affordable, it is still important to tend to it on a regular basis. If stucco is not maintained, it can look worn out and will cost you more money to repair the exterior. Here are some tips for caring for and maintaining exterior stucco:

Keep the Stucco Clean

Stucco can become dirty, easily, just like any exterior. Dirt can build up because of the outdoor elements, which can cause your home to look filthy. Stucco absorbs stains because of the porous material. Therefore it needs to be cleaned and maintained frequently. Using a power washer or garden hose can give the stucco a new and clean look. The best way to clean your stucco is to mist the exterior with water first to loosen up the dirt. 

After you mist the exterior, spray the garden hose or power washer with more pressure to allow the dirt to go on the ground. Cleaning the stucco will keep the exterior in good condition.

Take Care of the Repairs

One of the most important ways to care and maintain the exterior stucco is to fix any holes, cracks, or chips before it gets worse. When damages are not taken care of, it can affect the strength of the stucco material. Cracks, chips, and holes can also give an opportunity for pests to come into your home. If you notice a chip or crack in your stucco, repair it right away to prevent any further damage. If it is a minor crack, you can repair it yourself. A contractor may be needed if the damage is bigger. 

Seal the Stucco Regularly

When stucco is added to a home, it should always be sealed.  The stucco needs to be protected from any moisture. Usually, a clear concrete sealer is added to the stucco and stops moisture from getting inside the home. Although the clear concrete sealer is effective, it is important to seal the stucco every five years for protection.

Taking care of and maintaining the exterior stucco will help the stucco last for many years to come. These tips will have your house looking well-kept and protected from outside intrusions. Stucco is a wonderful exterior material and does not require a lot of maintenance. When you take care of any repairs, you will enjoy the appearance of your home.

For assistance, contact Chandler Stucco Contractors.

Top Tips For Maintaining a Hot Water Heater

hot water heater tank

The horror of running out of hot water when in dire need is definitely not a pleasant thought. Undoubtedly, hot water has become a bare necessity in every household, the reasons for which vary from showering to washing miscellaneous items. To avail this necessity at all times, it is important to understand how crucial it is for water heaters to be thoroughly maintained, because the alternative is nothing short of a nuisance in ghastly weather.

If you crave augmented efficiency, life extension, no petty issues, and saving money when it comes to water heaters, regular maintenance of it is vital. And therefore, lets delve into some of the ways you can get the most of out of your hot water heater without needing repair service.

Check for leaks

 A leaking water heater can add up to unnecessary repairing expenses, and a rise in utility bills. To avoid all kinds of relevant inconveniences, a hot water tank should be carefully examined for leakage, excessive rust, or water gathering at the base. In unfavourable circumstances like such, call a professional as soon as possible.

Drain the tank to get rid of sediment

A lot of sediment and foul residue tends to build up along the walls of the tank over time, which needs a proper cleaning every few months, in order to avoid water carrying a vile taste and smell. There’s an easy way to remove all the sediment, for which you need to clear out the tank first. Drain out the water from tank into buckets, and wash up the empty tank with cold water. The process is to be repeated till clear water comes out, and now you can refill the tank and are good for a few months at least.

Check and adjust the temperature

Time and again, you should check your water heater temperature, which should range from 55 to 60 degrees. You can easily adjust the dial using a flathead screwdriver. If you aim to save energy costs, reduce the temperature. If you’re planning on leaving the house for days, it’s best to turn the thermostat down to its lowest setting.

Examine the anode rod 

It is critical to also keep a check on the anode rod. The key is to drain a few gallons of water first, and then insert a 1 1/16-inch socket onto the rod’s hex head on top of the heater and unscrew the rod. Check whether its coated with calcium, or ½ inch thick. In such a case, you would need to insert a new one.

Test the TPR valve

In order to test the temperature-pressure-release valve, place a bucket under the pipe connected to it. Let some water out by lifting the valve’s tab, and then let go. If the water keeps flowing, you will need to install a new one. We recommend Aurora, Colorado water heater installation in the Denver area.

Along with these beneficial tips, it is also important to understand that gas and electric water heaters require different kind of maintenance. The key is to keep the filter, air vent, and spark arrester clean, and you’ve indefinitely got yourself a lasting water heater.

Tips For Moving A Washer & Dryer

Moving heavy appliances to a new location can be tough. However, it can be accomplished. If you are looking to transport a washer and dryer, you are probably going to want a couple of tips. The following are a few things to keep in mind when relocating these items.

Learn how To Disconnect them Safely

There are plenty of tasks you need to do in preparation. First, you should run a rinse cycle with a washer cleaner to make sure that your machine is as clean as possible. Then, leave the lid ajar to ensure that the insides dry out. You need to turn off the hot and cold water valves to the washer. Also, you should vacuum out your lint trap in the dryer.

Then, you need to shut off the electricity for disconnection. Finally, you will need to take out the water hoses from the wall. Providing that your dryer runs on gas, you must disconnect this line before moving. It is also important to secure the washer’s drum with shipping bolts.

Get Help From Friends

If you want to do the move on your own, then make sure that you enlist a couple of your friends. These need to be the type of people without health issues such as hernias. They all need to be able to do their part in lifting. When going up the stairs, you might only be able to have to people moving, so make sure these are the stronger ones in your group. You should also use forearm forklifts to make this possible.

Gather your Equipment

You will probably need a moving van to load these into. It is best to keep both the washer and dryer upright. If you turn them on their sides in a truck, make sure you secure them tightly. You will need to use rope. Using a tow strap that is adjustable will be the best move here.

There are moving companies in Detroit that specialize in moving all home appliances, including washers, dryers, refrigerators, stoves, dish washers, and more.

What causes a leaky faucet and how to repair it

leaky faucet

Leaky faucet always annoys and it’s a problem common at home which can disrupt the beauty of your sleep as well as take water bills at higher prices. Even with those small leaks, it can end up draining three water gallons in a day. If the leaking goes like for a year, you will note that water lost can even fill a swimming pool. Leaking faucet is caused by many reasons which depending on cause determine which way they will be fixed, whether you can do it yourself or need a plumber in Cheektowaga.

Causes of leaking faucet

Damaged O-ring

A major cause to leaks especially for cartridge faucets. Worn-out or loose O-ring is majorly associated with such. The O-ring is a small disc attached to faucet’s stem screw which holds the faucet’s handle in place. When it’s damaged, the faucet then drips near its handle.

Cartridge is worn

The cartridge in a cartridge faucet can also be a cause of leaking of the faucet. In such a case, replacement of the cartridge is the best solution to solve such issue. However, before swamping, you are required to ensure that the replacement cartridge matches the cartridge being replaced.

Valve seat is corroded

If you note the leak originates from the faucet’s spout, then the cause could be its valve seat. This is wat connects the spout to the faucet. When water sediments buildup there they might lead to corrosion of valve seat and hence leading to leaks. In order to avoid such corrosion, clean the seat generally and at times consider a professional to do the cleaning.

Washer problems

Spout leakages are also caused by washer problems as it seats against faucet’s valve seat. Due to friction over some period of time between the two points the washer could be worn-out. Incorrect installation of washer or installing under size or over size washer could also lead to leaks. Compression faucets mostly experience such issues.

How to repair a leaking faucet

Below are the steps you can follow to repair such issue:

  • Turn off water which is flowing into the sink. You not only need to turn off the tap only but also all the valves below your sink. Consider placing a bucket beneath the sink just in case water leaks out.
  • Begin your inspection of the faucet to determine which part is causing the leak. Inspect its handles as most of faucets have the handles as the cause of leaks. For faucets with caps you will need access to the screw securing the handle and you will need to loosen it so as to remove the handles form the faucet.
  • Disassemble your faucet then clean every part of it using calcium remover. Check any cracks for the gasket made of rubber. If cracked, you need to replace the faucet’s washer. In order to get the right one and avoid more leaking, carry with you the damaged gasket in order to purchase the right size.
  • After replacing required replacements, reassemble your faucet installing each part where it should be. Tighten the faucet in a secure place and ensure its attached firmly to your sink.
  • Turn water on to test if the faucet functions as required.

DIY: How to Remove Stains From Your Carpet


The process of carpet cleaning is not too lengthy and doesn’t require much hard work either if you know what you’re doing, that is. However, sometimes you’ll get a stain or two that just won’t leave. At such times you should think to call a professional service to remove a stain from your carpet.

Although a professional will know how to go about his job, there are a few things you should know as well, if you are going to remove stains by spending a lot of money. There are two ways of getting your carpet stain free: Steam cleaning and Dry cleaning. Both are quite effective while trying to remove stains and suited for most types of carpets. However, it’s best to check with your dealer or manufacturer, what they recommend

Dry Cleaning

Like the term suggests, this method does not require that your carpet is rinsed or made wet in any way. Different professionals use different methods to clear stains from carpet by dry cleaning. Some use a particular type of foam that doesn’t wet your carpet but attaches itself to the dirt and stain particles. This foam has to be then vacuumed. Some use a sawdust-like compound, only wet, instead of the foam. In both cases, the substance then has to be extracted. Some cleaners will have specific machines to do this job. In any case, dry cleaning is preferred if your carpet is made of delicate material and it is a much cheaper way for carpet stain removal than the other alternative.

Steam Cleaning

This is the most thorough way to do away with stains on the carpet. A piece of equipment rinses your carpet out using super-heated water. The water is forced into the carpet fibers and then sucked out, removing every last bit of dirt, germs, stain and fungus; rendering your carpet clean. Although a bit expensive, it is recommended by most manufacturers.

Choosing the Right Remodeling Projects for a Small Bathroom

When someone is taking a small bathroom and changing it up, they want to choose the changes that will mean the most to them and the use that they get from that space. Anyone who is taking on a bathroom remodeling project wants to do that in a way that will make the most of their bathroom. When someone has a small bathroom, they need to think about the ways that they can make it as useful as possible, the ways that they can make the space feel larger. It is important for a person to know what is best for them when it comes to remodeling a small bathroom.


When someone is taking on bathroom remodeling work and changing up a small bathroom, they need to consider the changes that will update the style of the bathroom. A small space might not have much decor in it, but changing out the vanity in a small bathroom will help to give the bathroom a new look. Changing out the mirror in the bathroom will alter the way that the whole space looks. There are small updates that can be made to modify the appearance of a small bathroom.

When someone is looking to complete bathroom remodeling work in their small bathroom, they should think about the setup that makes the most of the space that they have. They should consider the location of their toilet in comparison to the site of their sink and figure out where each component should be. The one who is hoping to make the most of a small bathroom should think about the layout of their bathroom and remodel it in a way that helps them move around with ease.

It is important for a person to know just what they are doing when they are remodeling a small bathroom. They have to know which changes will work out the best for them in the end. The one who is taking on bathroom remodeling work has to know which improvement projects are best for their small bathroom.

Upgrade Your Interior With a New Fireplace Mantel

Fireplace mantel designs have always been the interior decorator’s challenge, although their purpose has shifted slightly in the last fifty years. Earlier fireplaces were the main source of heat during cold winters. Large homes had a fireplace in each room, which was laborious to maintain, creating a mess alongside their cheerful warmth. The fireplace served as a natural focal point, drawing families to gather, and stood as an important decorative feature. Wealthier homeowners hired tradesmen to build elaborately carved mantels out of wood, stone or marble.

There are many ways to dress up a lonely fireplace, or even install one with a ventless insert and mantel. Besides using an existing fireplace for heat, you should never ignore its potential to breathe architectural character into a room.

Embellishing the Fireplace Mantel Design You Have

Many fireplace mantelpieces are just right the way they are, whether elaborately carved or sporting clean, classic lines. These details will help you take what you have and make yours even better.

Extend the Mantel

A half mantel includes the mantel shelf, framework, and surrounds of the fireplace. A full mantel (also called an overmantel) includes a panel that extends above the mantel shelf, sometimes to the ceiling. The full mantel can be achieved with wood paneling and encased in molding or mimicked by arranging thin strips of molding.

Add Built-in Features to Either Side

Open shelving on the sides of a fireplace mantel can effectively simulate a full mantel. Many moldings are available to enhance these shelves to fit the room.

Wall Features

Wall paneling on either side of the fireplace with chair rail molding adds class to a room and visually supports a fireplace in a large wall.

Redesigning the Fireplace Mantel and Surrounds

Do you have a boring, outdated fireplace or mantel? Here are a few ways to transform it.

Period fireplaces

It’s possible to buy a vintage salvaged fireplace, mantel and surrounds in nearly any period. This is a great option for those restoring older homes whose current “updated” fireplaces are completely out of step with the period of the home. It’s also an easy way to bring home the spectacular craftsmanship and millwork of yesteryear.

Reproductions or replacements

There are so many reasons to replace or add to what you have. Your mantel shelf may be too shallow, or non-existent. You may have only a lonely insert. You may hate the old style brick surrounds. A simple change of fireplace mantel shelves and surrounds can answer these problems and work wonders for the entire room. The choices are numerous: Hardwood mantelpieces can be simple or carved. The color of wood enriches the palette and offers the flexibility of painting or staining. Wood fireplace mantelpieces must meet fire safety codes, and sometimes need a fire-safe material for the surrounds, like tile, stone, or metal. Stone fireplace mantels can be elegant or rustic, using materials like limestone, travertine, slate, and marble.

Stone can also be used for the surrounds

Faux stone (also called cast stone) offers the realistic look of carved stone at a more reasonable price. Metal fireplace mantels come in vintage reproductions or sleek modern styles, with choices like copper, bronze, steel, pewter, and cast iron. With hand rubbed and verdigris finishes, metal can be a warm, enriching material choice.

With the above ideas, you may be rethinking fireplace mantel designs in your home, not only for your living room but for the dining room, master bedroom, home office, family room – once you see how a fireplace can bring life to a room it’s easy to get carried away… so go ahead, start planning!